|
Searched The Old-House-Friends Forums for "sheet metal"
|
Found 12 matches
|
|
<< Previous 10
| Viewing 1 - 10 of 12
| Next 10 >>
|
|
|
|
|
|
I have the same problem....temco is now majestic and vermont castings...so a majestic 94 pipe will work...there are 3 pipes with inner pipe 9...Im not sure about the size for the outter pipe...because I havent not installed the pipe yet. this is the only way to do it! or you have to order it from a ...
|
|
read more
|
|
|
|
|
|
|
My wife and I own a home that was built in 1920. As with most older homes, there are missing odds and ends. One item we are missing is a heat register. Weve looked everywhere for the right size but have come up empty handed each time. The inside measurements are 12w x 8h, with the base of the sheet ...
|
|
read more
|
|
|
|
|
|
|
Looking for old, rusty corrugated tin/metal sheets in say 2x8. Need 100+. Also maybe a supplier of unfinished corrugated metal. Live in southern Cal... Thanks
|
|
read more
|
|
|
|
|
|
|
There are those who may tell you that there are all kinds of shortcut methods you may use to correct this condition, however, you are right that you should have sealed your metal before you painted. You will have to strip the entire ceiling with a stripper and not walk away from it while the strippe...
|
|
read more
|
|
|
|
|
|
|
You dont say, are the tile ceramic or asphalt? If you use solvent on the asphalt it will damage the surface of the tile as well as removing the glue. And you MUST keep all the windows open so you dont blow up the house. You could likely pop off the tile as well, and redo the floor. You could belt sa...
|
|
read more
|
|
|
|
|
|
|
We have a number of rain lamps, some of which Ive repaired with success. Its too much to expect that any lamp found on Ebay is going to be ready to plug in and go. Theyre usually clogged up and dont take too well to being drained and refilled, especially if theyve been out of service for a time. You...
|
|
read more
|
|
|
|
|
|
|
ok you ask...your answer: I just provided this information ironically yesterday to someone who contacted me and here is part of the email of the exact information I provided the... Installing furing strips 6 inches apart across the tops of the rafters nailed on the full length of the building will g...
|
|
read more
|
|
|
|
|
|
|
cool that pics can be loaded and traced back to who loaded them so if someone posts their nude family album, they can be removed with their pics of grandma. If you can load some pics of your room with some close-ups of the wall to the window and air passthroughs inside and out, that would be cool. O...
|
|
read more
|
|
|
|
|
|
|
Without seeing your scounces, it is simply a guess in the dark as to what you have and how to proceed. There are some general rules based on generic facts that may help you preserve what you have until you can determine exactly what you have, so let me start there and see if that helps you out any. ...
|
|
read more
|
|
|
|
|
|
|
I am looking for stamped aluminum sheets similar to the stamped decorative metal used in doors of old pie safes . Preferably larger in size, like 2 X 3 or larger. I have looked all over but to no avail. Does anybody have any suggestions?
|
|
read more
|
|
|
|
|
<< Previous 10
| Viewing 1 - 10 of 12
| Next 10 >>
|
|
|
Searched The Old-House-Friends Forums for "sheet metal"
|
Found 12 matches
|
|
|
